Gamma 6900 Els STRINGING MACHINE 2 POINT SC MOUNTING (Is Uživatelský manuál

OWNER’S MANUALIssue 4B - February 20146900 ElsSTRINGING MACHINE2 POINT SC MOUNTING

11CONTROL PANEL FUNCTIONS AND FEATURESSingle Digit (1-9) Memory LED DisplayThree Digit (XX.X) Tension Setting Dis-play or String Length LED DisplayS

12MOUNTING THE FRAMEAdjusting the Inner Racquet SupportsThe white racquet supports are adjustable to accommodate all racquets and provide maximum

13Special Throat Mounting For racquets with a bridge that is thinner than the rest of the frame or are tapered from head to throat you may need to mou

14Setting the String TensionString tensions may be entered and stored into one of nine memory storage settings (See sec-tion on Control panel Function

15Clamping the First Main StringSecure the tensioned main string using the free fi xed clamp. Repeat the procedure for all of the remaining main string

16ADDITIONAL FEATURESCompleting the String JobOnce the fi nal cross string is tensioned and clamped, tie off at the appropriate hole speci-fi ed by the

17To enable the String Length Meter (SLM) function, press the String Length button on the keypad. When the String Length but-ton is pressed, one of th

18PATHFINDER AWLOnce the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in

19Tension Calibration ProcedureEach stringing machine has been checked and calibrated at the factory using accurate load sens-ing devices to ensure th

20Adjusting the String Clamp Jaw SpacingThe string clamps will need minor adjust-ments according to what string type, con-struction, and g

3OWNER’S MANUAL6900 ElsLIMITED WARRANTYGAMMA Sports (GAMMA) warrants to the original purchaser that the 6900 Els stringing machine (“EQUIPMENT”)

21TROUBLESHOOTING TIPSCARE & CLEANINGWith time and use, the clamping surfaces of your machine may become oily or dirty and result in string or cl

22NOTES

23 MFSC FLOOR STAND CASTERS MTC CALIBRATOR SGSM STRINGER’S MAT 5 RUBBER FOOT* 6B CAP SCREW- M8x30 106 STAND BRAKE KNOB 114 SHORT LEG 115

24PARTS DRAWING313E82MRSGD1063443433113491213473461142832852863623202893291153486B3276B337299312390345310MQAC12MDCSC13315304309314111210212389

GAMMA SPORTS 200 Waterfront DrivePittsburgh, Pennsylvania 15222 Phone: 800.333.0337 Fax: 412.323.0317 Visit our website at www.gammasports.comCopyrig

4 Electronic Constant Pull Tensioner with 11.0 to 90.0 lbs Tension Range Digital Tension Setting with LED Display Professional Self-Centering Tw

56900 ElsUnpacking Instructions & ContentsInstructions for Unpacking and Preparing for AssemblyThe stringing machine is shipped in three cartons,

6Floor Stand AssemblyThe stringing machine uses a four leg fl oor stand design. The legs must be as-sembled to the lower column before use. Remove all

7Transportation ScrewThe machine has been shipped with a motor and load cell protection screw. Remove the screw before using the machine. Retain the

8String Clamp InstallationThe post of the string clamp and tube of the string clamp base are treated with grease to provide protection against corrosi

9The string reel holder is an 8 mm rod with threads on both ends, and fl at surfaces machined on one end. Thread the end of the rod without the fl at su

10POWER CONNECTION & CONTROLSFront Panel FeaturesA - String GripperB - Tension SwitchC - Control PanelBack Panel FeaturesA - Lighted Power Sw